 |
| Thompson |
| T-100 Envelope Feeder
Only $117 per month
O.A.C.*
|
|
 |
|
 |
|
Easy-to-use, the Thompson T-100 is designed to maximize
envelope print production. This model is fully automated and
built-to-last. Its rugged construction and reliable service record means
the Thompson T-100 is built for the long run. |
|
 |
Fits any offset press |
|
Feeds a large variety of
envelope sizes |
|
Feeds unusual and
hard-to-feed stock |
|
Cuts production time in half |
|
Quick set up on or off the
press |
|
Installs in minutes and
simple to operate |
|
No synchronization to press |
|
Feeds up to 10,000 IPH |
|
Loads while press is running |
|
Compact size |
|
Low maintenance |
|
Built to last |
|
Five year warranty |
|
 |
|
|
|
|
| TECHNICAL SPECIFICATIONS: |
| MODEL: |
T-100 |
| LENGTH: |
36" |
| WIDTH: |
Between side covers: 15" Feder Table:
11" |
| HEIGHT: |
Maximum: Feed Table 38" Minimum: Feed Table
26" |
| BASE: |
Mobile (Mounted on rollers) |
| WEIGHT: |
90 lbs. |
| SPEED: |
Variable up to 10,000 envelopes per hour |
| STOCK SIZE: |
Variable from 3" x 5" up to 9" x
12" |
| CAPACITY: |
Loads 500 envelopes at a time |
| FITS: |
All small offset presses |
| POWER: |
115V, 60HZ, 220V (optional) |
| ACCESSORIES: |
Optional conveyor at delivery end |
|
|
|
|
The Thompson Envelope Stream Feeder was
designed as an automated helper for the printer. Once the feeder is set
up, it requires very little of the printers time except for keeping it
loaded. This gives the printer more time for quality printing and stock
control. The press can run continuously at any speed the printer
chooses. |
|
For years printers have struggled to print
envelopes and other hard to feed materials. Now the problem is solved
with the Thompson T-100 envelope Stream Feeder. With the feeder there is
no need to stop to reload, no more shimming, and no more loading small
amounts. Your press can run all day and print three to six times as many
envelopes. This means increased profits for every hour you run. Set up
time is fast and easy. The feeder loads from the top and feeds from the
bottom to keep a continuous stream of envelopes to the press and is
reloaded with the press running. This eliminates wasted time from stop,
load, and go envelope printing. It also helps prevent doubles from
sticky envelopes. |
|
The T-100 is a free standing unit mounted on
casters. The base height is adjustable to aid in leveling it to the
press. It can be set up on or off the press in less than three minutes.
It is set on the elevator table of the press and positioned between the
press stock guides. A rubber tarp strap holds it tight against the
press. When the job is finished, disconnect the tarp strap and roll it
away. |
|
The T-100 will stack eight to twelve
envelopes under the press sucker feet. The stack of envelopes is
controlled by a microswitch which keeps the stack a constant height at
all times. As the press picks up the envelopes the microswitch puts more
envelopes under the bottom of the stack. The feeder motor only runs when
the press needs more envelopes. No timing device is needed. The T-100
can feed in excess of 10,000 envelopes per hour and the speed of
printing is controlled by the printer. |
|
The T-100 is fully adjustable to feed from
3"x5" to 10"x13". Adjustment is fast and easy. Up to
500 envelopes can be loaded at a time and more can be added at any time
with the press running. There is no need to stop the press until the job
is finished. Big savings can also be made on short runs of hard to feed
envelopes or other hard to feed materials. |
|
The feeder is shipped with the side covers,
front and rear stock guides removed. It can be fully assembled with only
a Phillips head screwdriver. |
|
|
|
[Home]
[About Thompson] [Conveyor]
[Perforating Dies] [Perfect
Perforating Rules] [Offset
Perforating Rules]
[Rule Application]
[Plate Corrector] |
|
Copyright © 2001
All Rights Reserved. |
